Parameters

Skip Navigation LinksSupport > Knowledge Base > XL200 Series Controllers > Parameters

This will eventually be a complete listing of all XL200 controller parameters. Each parameter will describe what version it showed up in, along with its own history of functionality based on version.

Parameter Name

Help ID
 Shear Dwell Down  121
 Shear Dwell Up  122
 Shear Boost Dwell  123
 Shear Reaction  124
 Shear Boost Reaction  125
 Shear Boost Enable Velocity  126
 Expect Shear Complete  127
 Press X Dwell Down  Several
 Press X Dwell Up  Several
 Press X Boost Dwell  Several
 Press X Reaction  Several
 Press X Boost Reaction  Several
 Press X Boost Enable Velocity  Several
 Expect Press Complete X  Several
 Tool Selected for Manual Punch  260
 Punching Mode  267
 Bundle Quantity Reload Value  300
 Bundle Quantity Count  301
 Item Complete  302
 Delay After Shear  303
 Short Part Delay  303
 Very Short Part Delay  303
 Minimum Slow Distance  304
 Scrap Part Length  305
 Auto Crop Length  305
 Halt Mode  306
 Halt No More Items to Run  307
 Stopping Reaction Mode  309
 Stopping Reaction Time  310
 Deceleration Mode  311
 Deceleration Factor  312
 Tolerance  313
 Stitch Gag  316
 Max Auto Stitch Length  317
 Slow Output While Halted  318
 Stacker Dwell  319
 Stacker Delay  319
 Parts Per Stack  319
 Horn Dwell  320
 Crash Detect Velocity Change  321
 Crash Detect Time  321
 Dump Table Delay  325
 Dump Table Dwell  326
 Mist Counter  327
 Mist Delay  328
 Mist Dwell  329
 Test Part Length  330
 Tolerance Mode  331
 Continuous Material Flow  332
 Use Coil Inventory  333
 Allow Coil Override  334
 Dump Mode  335
 Bump Tolerance  338
 Bump Time  339
 Stopping Distance  340
 Uncut Length Threshold  341
 Stitch Mode  342
 PCode Change Stops Queue  343
 Coil End Point  350
 Coil End Offset  351
 Encoder Direction  352
 Shear Kerf  353
 Minimum Part Length  354
 Shear to Encoder Distance  355
 Shear To Scrap Detect Distance  356
 Manual Scrap Chop Length  357
 Scrap Chop Length  358
 Minimum Die Distance  360
 Maximum Die Distance  361
 Shear Die Distance  362
 Reference Die on Manual Shear  363
 Clear Queue After  372
 Enable Shear Encoder Distance 2  373
 Shear Encoder Distance 2  374
 Coil Trim Cut Distance  375
 Front Shear Tool  376
 Front Shear Advance  377
 Maximum Part Length  388
 Short Part Length  399
 Very Short Part Length  399
 Hole Mode Select  400
 No Hole Stop Distance  401
 Minimum Hole Spacing  403
 Shear to Detector Distance  404
 (Line) Resolution  450
 Die Resolution  452
 Loop Gain  453
 Offset Integral  454
 Offset Voltage (Auto)  455
 Lag Integral  456
 Lag Compensation (Auto)  457
 Derivative  458
 Jog Select Mode  461
 Jog Velocity  462
 Minimum Die Return Velocity  463
 Slow Run Velocity  464
 Maximum Die Return Velocity  465
 Maximum Velocity  466
 Acceleration  467
 Return Acceleration  468
 Die Reference  469
 Advance After Cut  472
 Retract After Cut  473
 Offset Integral Delay  475
 Lag Comp. Integration Limit  476
 Velocity at Max Analog Voltage  500
 Auxiliary Shear Compensation  501
 Filter Constant  503
 Minimum Speed Voltage  504
 Maximum Speed Voltage  505
 Length at Maximum Speed  506
 Jog Speed Voltage  507
 Max Die Count  508
 Die Travel (Auto)  509
 Start Position  510
 Speed Reduction  511
 Die Home Reference Angle  512
 Coast Mode Timeout  520
 Crankshaft Length  521
 Crankshaft Offset  522
 Fly Wheel Radius  523
 Time Format  600
 Date Format  601
 Date Separator  602
 Set Hours  603
 Set Minutes  604
 Set Seconds  605
 Set AM or PM  606
 Set Days  607
 Set Months  608
 Set Year  609
 IP Address  615
 IP Subnet Mask  615
 IP Gateway  615
 MAC Address  615
 Network Unit ID  650
 Network Baud Rate  651
 Halt Delay Minimum  652
 Auto-Request Order Footage  653
 Use Scrap Codes  654
 Manual Shear Scrap Length  655
 Eclipse Source  657
 Language Select  700
 Numeric Display Format  701
 Auto-Delete Done Orders After  702
 Set Done Items to Ready  703
 Enable Virtual Keyboard  704
 Show User Data - Program Screen  707
 Show User Data - Status Screen  708
 Show Help Preview - Setup Screen  709
 Stagger Panel Field  710
 Enforce Configuration By PCode  711
 Last Programmed Length  775
 Last Measured Length  776
 Correction Factor  777
 Parts in Queue (Auto)  778